Skip to Content

CERESIT CT 325 GLASS-FIBRE MESH

  • Alkali-resistant
  • Slipproof
  • Tearproof

Features and benefits

Reinforcing mesh for Ceresit Ceretherm External Thermal Insulation Composite Systems.

Properties

Description

CERESIT® CT 325 is reinforcing mesh for embedding into reinforcing mortars for CERESIT External Thermal Insulation Composite Systems (ETICS). For façades or pedestals exposed to higher mechanical loads, it is preferred to use CT 325 in two layers or use higher density mesh of 330 g/m Available pack size: 1,1 m width and 50 m length

Documents and downloads

How to use

CERESIT Tiling CE60 LP Instructions Illustration Step 1

APPLICATION OF CERESIT CT 325

Prepared CERESIT reinforcing mortar should be spread evenly over the surface of the boards with a tooth trowel with teeth the size of 10-12mm. In the case of mineral wool boards prior to distribution must also make ”priming” with mortar. In the prepared layer immediately spread fiberglass mesh, then embed by using a metal trowel and make it smooth. Properly applied mesh should not be visible and completely embeded in the mortar. It is important to keep the mesh overlaps on next applied belts to about 10 cm. Bets of mesh can not coincide with the joints between the panels.

CERESIT Tiling CE60 LP Instructions Illustration Step 2

IMPORTANT TO NOTE WHEN USING CERESIT CT 325

Please refer also to the technical data sheets of other products in the CERESIT ETICS systems for specific advice on how to prepare the substrate and execute the work. Please refer in particular to ETAG 004. Therefore, skin and eyes should be protected. In case of contact with eyes, they should be rinsed with water and a general practitioner should be consulted. 

Related how to guides

  • How to apply different types of plasters?
    How to apply different types of plasters?
  • How to apply architectural concrete plaster
    How to apply architectural concrete plaster?
  • Fix EPS insulation boards with adhesive mortar?
    How to fix EPS insulation boards with adhesive mortar?
  • Fix EPS insulation boards with PU adhesive?
    How to fix EPS insulation boards with PU adhesive?
  • How to repair mechanical damages in plastered insulation?
    How to repair mechanical damages in plastered insulation?
  • How to prepare the substrate for installation of the insulation layer
    How to prepare the substrate for installation of the insulation layer
  • Decorative plaster with visage stone effect
  • How to cope with bio contamination on facade

Related products

  • ${/content/heliux/adhesive/ceresit/com/en/products/facade-solutions/product#/ceresit-ct-327/SAP_0201IJC014H3/searchResult.productFields.MainImageAltText}
    CERESIT CT 327
    Reinforcing mesh for Ceresit Ceretherm External Thermal Insulation Composite Systems. 
  • ${/content/heliux/adhesive/ceresit/com/en/products/facade-solutions/product#/ceresit-thermo-universal/SAP_0201IAC015R0/searchResult.productFields.MainImageAltText}
    CERESIT THERMO UNIVERSAL
    Reinforcing Rendering Mortar - Basic coating XPS, EPS, MW. 
  • ${/content/heliux/adhesive/ceresit/com/en/products/facade-solutions/product#/ceresit-ct-85/SAP_0201IAC014M9/searchResult.productFields.MainImageAltText}
    CERESIT CT 85
    For fixing Expanded Polystyrene (EPS) boards as well as for applying a thin armoured layer for thermal insulation of buildings by means of light wet method. 
  • ${/content/heliux/adhesive/ceresit/com/en/products/facade-solutions/product#/ceresit-ct-74/SAP_0201IDC014L4/searchResult.productFields.MainImageAltText}
    CERESIT CT 74
    Decorative thin-layer plaster for indoor and outdoor applications, stone structure, grain 1.5, 2.0 or 2.5 mm 
  • ${/content/heliux/adhesive/ceresit/com/en/products/facade-solutions/product#/ceresit-ct-190/SAP_0201IAC014F9/searchResult.productFields.MainImageAltText}
    CERESIT CT 190
    For fixing Mineral Wool boards as well as for applying a thin-armoured layer for thermal insulation of buildings in ETICS systems. 

Frequently asked questions