Skip to Content

CERESIT CT 180 MW STRONG FIX

  • High adhesion to mineral substrates and mineral wool
  • Very good workability
  • Resistant to weather conditions

Features and benefits

For fixing Mineral Wool boards for thermal insulation of buildings by means of ETICS and for insulating ceilings of garages.

Properties

Description

CERESIT® CT 180 is designed to warm up external walls of the buildings by application of external thermal insulation composite system using mineral wool façade boards as well as lamella. It is an element of CERESIT Ceretherm WM Classic and WM Premium insulation systems. CT 180 is used for fixing of mineral wool façade boards to insulate the newly erected objects as well as the buildings to be thermo-renovated. it should be used in case of EPS-boards application used for insulating buildings. Available pack size: 25 kg

Documents and downloads

How to use

CERESIT Tiling CE60 LP Instructions Illustration Step 1

CERESIT CT 180 SUBSTRATE PREPARATION

CERESIT CT 180 shows good adhesion to carrying, compact, dry and clean substrates free from substances decreasing adhesion of surfaces of walls, plasters and concretes. The adhesion to the existing plasters and paint coatings should be checked before starting the application. Any losses and uneven surfaces should be filled or covered. Any surface contaminant and other adhesion impairing substances, steam-tight paint coatings and the coats with low adhesion to the substrate should be removed.

CERESIT Tiling CE60 LP Instructions Illustration Step 2

APPLICATION OF CERESIT CT 180

CERESIT CT 180 should be poured into water and stirred until the homogenous mass is obtained without lumps. It is necessary to apply “priming” layer with CT 180 on MW bards before proper application of mortar, than on top of “priming”, right after ready mixed mortar should be applied along the board edges. Then immediately, the board should be pressed to the wall with a few slight blows of a long float. 

CERESIT Tiling CE60 LP Instructions Illustration Step 3

IMPORTANT TO NOTE WHEN USING CERESIT CT 180

Application should be performed in dry conditions with the substrate and ambient temperature from +5 °C to +25 °C. Skin and eyes should be protected. In case of contact with eyes, they should be rinsed with water and a general practitioner should be consulted. 

Related how to guides

  • How to apply different types of plasters?
    How to apply different types of plasters?
  • How to apply architectural concrete plaster
    How to apply architectural concrete plaster?
  • Fix EPS insulation boards with adhesive mortar?
    How to fix EPS insulation boards with adhesive mortar?
  • Fix EPS insulation boards with PU adhesive?
    How to fix EPS insulation boards with PU adhesive?
  • How to repair mechanical damages in plastered insulation?
    How to repair mechanical damages in plastered insulation?
  • How to prepare the substrate for installation of the insulation layer
    How to prepare the substrate for installation of the insulation layer
  • Decorative plaster with visage stone effect
  • How to cope with bio contamination on facade

Related products

  • ${/content/heliux/adhesive/ceresit/com/en/products/facade-solutions/product#/ceresit-ct-190/SAP_0201IAC014F9/searchResult.productFields.MainImageAltText}
    CERESIT CT 190
    For fixing Mineral Wool boards as well as for applying a thin-armoured layer for thermal insulation of buildings in ETICS systems. 
  • ${/content/heliux/adhesive/ceresit/com/en/products/facade-solutions/product#/ceresit-ct-16/SAP_0201IGC014E8/searchResult.productFields.MainImageAltText}
    CERESIT CT 16
    Dispersion of synthetic resins to prime the substrates for thin layer mineral, acrylic, silicate-silicone, silicone and elastomeric plasters. 
  • ${/content/heliux/adhesive/ceresit/com/en/products/facade-solutions/product#/ceresit-ct-174/SAP_0201IDC014F2/searchResult.productFields.MainImageAltText}
    CERESIT CT 174
    Decorative thin layer plaster for indoor and outdoor applications, stone like structure, grain 1.5 mm or 2 mm. 
  • ${/content/heliux/adhesive/ceresit/com/en/products/facade-solutions/product#/ceresit-ct-15/SAP_0201IGC014E6/searchResult.productFields.MainImageAltText}
    CERESIT CT 15
    Silicate dispersion composition of potassium and acrylic to prime the substrates for thin layer silicate plasters, putties and paint coats. 
  • ${/content/heliux/adhesive/ceresit/com/en/products/facade-solutions/product#/ceresit-ct-175/SAP_0201IDC014F4/searchResult.productFields.MainImageAltText}
    CERESIT CT 175
    Decorative thin-layer plaster for indoor and outdoor applications, woodworm like structure, grain 2 mm. 

Frequently asked questions